SKILLS PORTAL

ព្រះរាជាណាចក្រកម្ពុជា · KINGDOM OF CAMBODIA

Cambodian Skills Delivery Model

SEAL National Course Catalogue · MLVT / National Training Board

Sector Frameworks

1,164

Qualifications

15,161

Competency Units

10,938

Elements

41,782

Learning Outcomes

2,822

Assessment Packages

Remove, inspect and fit earthmoving and off-the-road wheel and rim assemblies

KHU-AUT-0232

Australian Equivalent

AURKTJ112

Elements

Learning Outcomes

This unit describes the performance outcomes required to remove, inspect and fit earthmoving and off-the-road (OTR) wheel and rim assemblies and fasteners for fitment. It involves assessing and controlling risks, preparing for the task, removing, inspecting and refitting wheel and rim assemblies, inflating the tyre and completing workplace processes and documentation. It applies to those who fit wheel and rim assemblies of equal to or greater than 600 mm (24 inches) nominal diameter. The tyres must be classified as off-the-road, earthmover or industrial tyres.

Elements & Learning Outcomes

E1Assess and control risks

0232.E1.O1Identify hazards and control risks in the work environment according to workplace procedures

0232.E1.O2Identify and control hazardous wheel and rim assembly conditions, noting points where safety checks and controls are required

0232.E1.O3Obtain and interpret emergency procedures and be prepared for fires, accidents and emergencies

E2Prepare to remove wheel and rim assembly from vehicle

0232.E2.O1Obtain and interpret Original Equipment Manufacturer (OEM) instructions and specification, workplace procedures, safety information and applicable standards for earthmoving and OTR tyres

0232.E2.O2Obtain, interpret, clarify and confirm work requirements

0232.E2.O3Plan sequence of work, noting points where safety checks and controls are required

0232.E2.O4Select and wear personal protective clothing and equipment required for work activities

0232.E2.O5Coordinate and communicate planned activities with others at the site as per work requirements

0232.E2.O6Select and inspect tools and equipment according to OEM specification and workplace procedures

0232.E2.O7Identify wheel and rim assembly type, fastening system and handling equipment required to complete work activity

0232.E2.O8Clean wheel and rim assembly, and inspect visually for damage, wear, corrosion, foreign material, cracks and compatibility of components to assess potential health and safety threats according to workplace procedures

E3Remove wheel and rim assembly from vehicle

0232.E3.O1Isolate, raise and support vehicle according to workplace procedures

0232.E3.O2Deflate tyre before removal of fasteners and from vehicle according to workplace procedures, OEM requirements and Australian Standards

0232.E3.O3Verify appropriate deflation of tyre in line with workplace procedures, OEM requirements and Australian Standards

0232.E3.O4Remove tyre, wheel and rim assembly according to workplace procedures and without causing component damage or injury

0232.E3.O5Apply workplace procedures for transport and storage of wheel and rim assembly

E4Inspect mounting surfaces and fasteners

0232.E4.O1Visually inspect mounting components, fasteners and surfaces for damage, wear, corrosion, foreign material and cracks according to OEM specification and workplace procedures, and discard damaged fasteners

0232.E4.O2Record and report findings according to workplace procedures

E5Fit wheel and rim assembly

0232.E5.O1Compare condition of wheel and rim assembly against OEM specification and ensure it is suitable for application, managing non-conformance as per workplace procedures

0232.E5.O2Assess cleanliness of mating surfaces, and clean where required

0232.E5.O3Fit tyre, wheel and rim assembly using handling equipment according to workplace procedures

0232.E5.O4Check positioning and alignment of wheel and rim assembly prior to fastening

0232.E5.O5Vertically mount wheel and rim assembly in accordance with workplace procedures

0232.E5.O6Apply wheel and rim assembly tightening sequence and torque settings according to OEM specification and workplace procedures

E6Inflate tyre

0232.E6.O1Identify and apply tyre inflation safety procedures and establish exclusion zones prior to inflating tyre

0232.E6.O2Assess need for nitrogen and add where required

0232.E6.O3Inflate tyre according to workplace procedures and OEM specification

0232.E6.O4Monitor tyre, wheel and rim assembly during inflation according to workplace procedures

0232.E6.O5Verify inflation pressure according to workplace procedures and OEM specification

E7Complete work processes

0232.E7.O1Lower vehicle according to workplace procedures

0232.E7.O2Re-check wheel and rim fastener torque settings according to workplace procedures and OEM specification

0232.E7.O3Check wheel and rim assembly clearances according to OEM specification

0232.E7.O4Perform final inspection to ensure work meets workplace requirements

0232.E7.O5Inspect and store tools and equipment according to workplace procedures, tagging or reporting where necessary

0232.E7.O6Complete workplace documentation according to workplace procedures