Cambodian Skills Delivery Model

SEAL National Course Catalogue · MLVT / National Training Board

Sector Frameworks

1,164

Qualifications

15,161

Competency Units

10,938

Elements

41,782

Learning Outcomes

2,822

Assessment Packages

Install windows and doors

KHU-CON-0114

Australian Equivalent

CPCCCA3010

Elements

Learning Outcomes

This unit of competency specifies the skills and knowledge required to plan, prepare and install window and door units, meeting all relevant requirements of the National Construction Code (NCC), Australian Standards, work health and safety (WHS), and Commonwealth and state or territory legislation. Completion of the general construction induction training program specified by the model Code of Practice for Construction Work is required for any person who is to carry out construction work. Achievement of CPCWHS1001 Prepare to work safely in the construction industry meets this requirement. No licensing, legislative or certification requirements apply to this unit at the time of publication.

Elements & Learning Outcomes

E1Plan and prepare.

0114.E1.O1Read and interpret work instructions and plan sequence of work.

0114.E1.O2Plan all work to comply with laws and regulations, the National Construction Code (NCC), Australian Standards, work health and safety (WHS) and environmental requirements, manufacturers’ specifications, workplace requirements, drawings and specifications.

0114.E1.O3Select tools and equipment, check for serviceability and report any faults.

0114.E1.O4Select and use personal protective equipment (PPE) as required for each stage of the task.

0114.E1.O5Inspect work site, locate services, assess hazards and apply risk controls, including required signage and barricades.

0114.E1.O6Select materials required for task, calculate quantities, handle safely and prepare and position ready for use.

E2Install window units.

0114.E2.O1Check wall frame opening for adequate clearance for window unit.

0114.E2.O2Position window unit with packing and flashings so that the head and sill are level, stiles are plumb and in wind, and reveals or frame are finished flush with face of inside wall lining.

0114.E2.O3Select type, gauge and quantity of fasteners as per Australian Window Association - An Industry Guide to the Correct Fixing of Windows and Doors and fix window to wall frame.

E3Prepare internal and external door openings, and construct and fix jamb.

0114.E3.O1Check wall frame for adequate clearance for door frame.

0114.E3.O2Mark door jamb and head, cut to length, allowing for door clearances.

0114.E3.O3Trench the door head to accommodate jambs, allowing for specified clearances.

0114.E3.O4Assemble, square, fix and brace door frame with flush rebates.

0114.E3.O5Select type, gauge and quantity of fasteners as per Australian Window Association - An Industry Guide to the Correct Fixing of Windows and Doors. Install door frame into wall frame opening, ensuring the door jambs are plumb and in wind, positioned flush to linings, head is level, and all appropriate flashings are in place.

E4Install door.

0114.E4.O1Mark out hinges and fit to door and jamb.

0114.E4.O2Fit door to frame and adjust gaps to requirements of AS2688 Timber and composite doors.

0114.E4.O3Fit and fix door furniture and door stop components to manufacturers’ specifications.

E5Install cavity door and door unit.

0114.E5.O1Fit hardware (rollers) to door according to manufacturer’s specifications.

0114.E5.O2Fit door to cavity sliding door unit and adjust height of rollers to ensure leading door edge is plumb and closes neat against cavity sliding door stile.

0114.E5.O3Make final adjustments to packing of cavity sliding door stile.

0114.E5.O4Fit and fix door furniture and cavity door centring locators, according to manufacturer’s specifications.

E6Clean up.

0114.E6.O1Clean up, meeting all legislative and workplace requirements for safety, waste disposal and materials handling.

0114.E6.O2Check, maintain and store tools and equipment and report any faults.