SKILLS PORTAL

ព្រះរាជាណាចក្រកម្ពុជា · KINGDOM OF CAMBODIA

Cambodian Skills Delivery Model

SEAL National Course Catalogue · MLVT / National Training Board

Sector Frameworks

1,164

Qualifications

15,161

Competency Units

10,938

Elements

41,782

Learning Outcomes

2,822

Assessment Packages

Apply float and render to straight and curved surfaces

KHU-CON-0323

Australian Equivalent

CPCCSP3001

Elements

Learning Outcomes

This unit specifies the skills and knowledge required to float, render and finish flat and curved solid plastering work. A person working at this level would be expected to take responsibility for organising and completing tasks assigned to them, without close supervision. Completion of the general construction induction training program specified by the model Code of Practice for Construction Work is required for any person who is to carry out construction work. Achievement of unit C PCWHS1001Prepare to work safely in the construction industry meets this requirement. No licensing, legislative or certification requirements apply to this unit at the time of publication.

Elements & Learning Outcomes

E1Plan and prepare to apply float and render to straight and curved surfaces.

0323.E1.O1Read and interpret work instructions and plan sequence of work.

0323.E1.O2Plan all work to comply with laws and regulations, Australian Standards, work health and safety (WHS) and environmental requirements, manufacturers’ specifications, and workplace requirements.

0323.E1.O3Select and use personal protective equipment (PPE) for each stage of the task.

0323.E1.O4Inspect work site, assess hazards and apply risk controls, including required signage and barricades.

0323.E1.O5Select tools and equipment, check for serviceability and report any faults.

0323.E1.O6Select materials required for task, calculate quantities, handle safely and prepare and position ready for use.

0323.E1.O7Select and use profiles, pins or hooks to prepare columns and piers.

E2Prepare templates for curved work and circular columns.

0323.E2.O1Select template material for curved work and circular columns.

0323.E2.O2Establish shapes and radiuses for curves and columns, and fabricate and form templates.

E3Prepare background surface.

0323.E3.O1Prepare background surface by brooming, wire brushing, scarifying and cleaning.

0323.E3.O2Mix dash coat and apply to wetted surface.

0323.E3.O3Apply bonding coat.

0323.E3.O4Select and fix proprietary/metal beads for external or squint arises and check for accuracy.

E4Apply floating and rendering to flat and curved surfaces.

0323.E4.O1Establish screeding lines or guides to Australian Standard HB161 Standards and tolerances guide to solid plastering.

0323.E4.O2Apply floating coat and rule off to screed.

0323.E4.O3Finish, plumb and level surface to alignment tolerance.

0323.E4.O4Finish heads, reveals and sills square off to wall ace and back into opening.

0323.E4.O5Cut internal angles, ceilings and floor lines.

E5Apply floating and rendering coats to piers.

0323.E5.O1Apply floating coat using floating profiles, rules and Dutch pins or hooks so that face of pier is plumb and ruled-off.

0323.E5.O2Square-off surface to form returns and reveals, and remove rules leaving arises square or radiused.

E6Apply floating coat within metal beading.

0323.E6.O1Fix proprietary/metal beading to base surface to form a panel with expansion joint so that panel is plumb and square to specified position.

0323.E6.O2Finish panels to true, flat surfaces suitable for applying plaster and lime setting and/or proprietary texture finishes.

E7Finish rendering coats on flat walls, piers and curved work.

0323.E7.O1Hand-float walls to fill slacks and voids to finish surfaces.

0323.E7.O2Scour and fine walls using water and hand float systems.

E8Clean up.

0323.E8.O1Clear work area, dispose of materials, and reuse or recycle in compliance with legislation, regulations and codes of practice.

0323.E8.O2Clean, check, maintain and store tools and equipment in accordance with manufacturers’ recommendations.