SKILLS PORTAL

ព្រះរាជាណាចក្រកម្ពុជា · KINGDOM OF CAMBODIA

Cambodian Skills Delivery Model

SEAL National Course Catalogue · MLVT / National Training Board

Sector Frameworks

1,164

Qualifications

15,161

Competency Units

10,938

Elements

41,782

Learning Outcomes

2,822

Assessment Packages

Carry out cemetery monument fixing

KHU-CON-0347

Australian Equivalent

CPCCST3013

Elements

Learning Outcomes

This unit specifies the skills and knowledge required to construct and fit cemetery monuments. It includes the use of granite, marble, basalt, pre-cast concrete sections and manufactured stone. This unit applies to stonemasons who work independently, in a team or under supervision to carry out stonemasonry work relating to cemetery monument fixing in a workshop setting, on a new or existing structure. A person working at this level would be expected to take responsibility for organising and completing tasks assigned to them without needing close supervision. Completion of the general construction induction training program specified by the model Code of Practice for Construction Work is required for any person who is to carry out construction work. Achievement of CPCWHS1001 Prepare to work safely in the construction industry meets this requirement. No licensing, legislative or certificat

Elements & Learning Outcomes

E1Plan the work.

0347.E1.O1Read, interpret and apply monument fixing requirements from current job instructions, specifications and codes.

0347.E1.O2Follow relevant information from workplace procedures, workplace safety and environmental documentation.

0347.E1.O3Determine job priorities and sequence job tasks in consultation with others on site.

0347.E1.O4Identify potential hazards and determine and implement control measures.

0347.E1.O5Use measurements and apply formulas to calculate material quantities.

0347.E1.O6Select and check condition of plant, equipment and tools and report damage or malfunction to relevant personnel.

0347.E1.O7Check conformity of materials against the job requirements and report inconsistencies to relevant person.

E2Construct footings and prepare monument stones.

0347.E2.O1Select, fit correctly and use personal protective equipment (PPE) appropriate for job.

0347.E2.O2Set out and excavate trench to specified dimensions.

0347.E2.O3Place reinforcement, fix formwork and pour concrete footings.

0347.E2.O4Set out and install monument on footing.

E3Position side stones.

0347.E3.O1Position side stones, plumb and pack to provide a slight fall towards front stone.

0347.E3.O2Check side stones are aligned, level, parallel and square.

0347.E3.O3Measure, mark, cut and insert abutting dowels.

E4Stand front and back stones.

0347.E4.O1Mix mortar, insert into side stone holes and insert dowel joints to full depth.

0347.E4.O2Position back stone on timber packing in preparation to lift into place and protect side stones to prevent chipping.

0347.E4.O3Place mortar and lift back stone into position and pack level.

0347.E4.O4Locate, raise and position front stone and pack to ensure level and plumb.

0347.E4.O5Mix grout and pack joints between base and kerb stones.

0347.E4.O6Remove excess grout and clean and wash kerb stones.

E5Fix headstone to back stone.

0347.E5.O1Measure and cut dowels for joints, apply mortar or adhesive and insert dowels.

0347.E5.O2Raise and lower headstone into position and finish plumb and level.

E6Fill centre and finish with chip top.

0347.E6.O1Fill and compact centre area base to specified height.

0347.E6.O2Place brick supports in each corner, cut and fix reinforcement and pour a minimum 50 mm concrete slab.

0347.E6.O3Mix and spread stone screening to required finished height.

E7Fit cover stone and finish monument.

0347.E7.O1Measure and cut dowels for joints, prepare and fill centre area and fill dowel holes with mortar and fully insert dowels into position.

0347.E7.O2Shift cover stone into place on timber packing, and lower into place using wedges to finish in position.

0347.E7.O3Prepare and apply pointing/grouting material to finish joints.

0347.E7.O4Remove excess mortar, and clean and polish cover stone.

E8Clean up.

0347.E8.O1Clear the work area, and dispose of, reuse or recycle materials following workplace and environmental requirements.

0347.E8.O2Clean tools and equipment, check for serviceability and report damage or faults.

0347.E8.O3Store and secure tools and equipment following workplace procedures.