SKILLS PORTAL

ព្រះរាជាណាចក្រកម្ពុជា · KINGDOM OF CAMBODIA

Cambodian Skills Delivery Model

SEAL National Course Catalogue · MLVT / National Training Board

Sector Frameworks

1,164

Qualifications

15,161

Competency Units

10,938

Elements

41,782

Learning Outcomes

2,822

Assessment Packages

Apply waterproofing process to external above-ground wet areas

KHU-CON-0394

Australian Equivalent

CPCCWP3003

Elements

Learning Outcomes

This unit specifies the skills and knowledge required to apply waterproofing to external above-ground wet areas, meeting all relevant requirements of Australian Standards, work health and safety (WHS) requirements, and Commonwealth and state or territory legislation. It includes identification of the appropriate waterproofing system to be used, its preparation and its application. A person working at this level would be expected to take responsibility for organising and completing tasks assigned to them without close supervision. Completion of the general construction induction training program specified by the model Code of Practice for Construction Work is required for any person who is to carry out construction work. Achievement of CPCWHS1001 Prepare to work safely in the construction industry meets this requirement. No licensing, legislative or certification requirements apply to thi

Elements & Learning Outcomes

E1Plan and prepare to apply waterproofing process to external above-ground wet areas.

0394.E1.O1Read and interpret work instructions and plan sequence of work.

0394.E1.O2Select and use personal protective equipment (PPE) as required for each stage of the task.

0394.E1.O3Plan all work to comply with laws and regulations, Australian Standards, work health and safety (WHS) and environmental requirements, manufacturers’ specifications, workplace requirements, drawings and specifications.

0394.E1.O4Follow requirements of job safety analyses and safety data sheets.

0394.E1.O5Inspect work site, assess hazards and apply risk controls, including required signage and barricades.

0394.E1.O6Select tools and equipment, check for serviceability and report any faults.

0394.E1.O7Select materials required for task, calculate quantities, handle safely and prepare and position ready for use.

E2Select waterproofing system.

0394.E2.O1Locate external above-ground area to be waterproofed from drawings and specifications.

0394.E2.O2Check area for soundness and surface defects.

0394.E2.O3Select waterproofing systems suitable for and compatible with site conditions and substrate.

E3Prepare for waterproofing installation.

0394.E3.O1Set out above-ground external wet area and check alignment, fixtures and finished levels for conformity with drawings and specifications, and report defects.

0394.E3.O2Test moisture content in substrate for compatibility with system and report defects.

0394.E3.O3Check adequacy of drainage and report defects.

0394.E3.O4Prepare flashings and termination seals and make ready for installation to manufacturers’ specifications.

0394.E3.O5Check that substrate has a uniform finish to manufacturers’ instructions.

0394.E3.O6Clean and prepare substrate ready for waterproofing and sealant.

0394.E3.O7Prime substrate ready for waterproofing and sealant.

E4Apply waterproofing.

0394.E4.O1Apply waterproofing system to prepared surface to manufacturers’ specifications.

0394.E4.O2Detail and terminate waterproofing membrane in accordance with system requirements.

0394.E4.O3Check completed waterproofing installation for conformity to manufacturers’ specifications.

0394.E4.O4Document movement joints for subsequent trades.

0394.E4.O5Perform final inspection and completion activities.

0394.E4.O6Protect waterproofing membrane.

E5Apply sealants to construction joints.

0394.E5.O1Select sealant for compatibility with application, substrate and finishes.

0394.E5.O2Install backing rods and/or release agents to prevent three-sided adhesion.

0394.E5.O3Apply sealant manufacturers’ specifications, tool to required finish and allow to cure.

0394.E5.O4Perform final inspection and completion activities.

0394.E5.O5Protect sealant, in accordance with manufacturers’ specifications.

E6Clean up.

0394.E6.O1Clear work area, dispose of materials, and reuse or recycle in compliance with legislation, regulations and codes of practice.

0394.E6.O2Clean, check, maintain and store tools and equipment in accordance with manufacturers’ recommendations.