SKILLS PORTAL

ព្រះរាជាណាចក្រកម្ពុជា · KINGDOM OF CAMBODIA

Cambodian Skills Delivery Model

SEAL National Course Catalogue · MLVT / National Training Board

Sector Frameworks

1,164

Qualifications

15,161

Competency Units

10,938

Elements

41,782

Learning Outcomes

2,822

Assessment Packages

Assemble internal shopfitting units and prepare for transport

KHU-CON-0577

Australian Equivalent

CPCSHP3004

Elements

Learning Outcomes

This unit of competency specifies the skills and knowledge required to assemble internal pre-cut components in an off-site manufacturing premises. It includes attaching fittings to the shopfitting units and preparing them for safe transport to the installation worksite. It applies to shopfitters involved in the final production stages of assembling shopfitting units prior to installation on a commercial site. Individuals at this level take responsibility for organising and completing these tasks with a high degree of self-direction. No licensing, legislative or certification requirements apply to this unit of competency at the time of publication. Completion of the general construction induction training program, specified in the Safe Work Australia model Code of Practice: Construction Work , is required by anyone carrying out construction work. Achievement of CPCWHS1001 Prepare to work

Elements & Learning Outcomes

E1Plan and prepare to assemble internal shopfitting units.

0577.E1.O1Identify, read and interpret job requirements from plans and specifications.

0577.E1.O2Apply organisational quality procedures and processes for assembling shopfitting units.

0577.E1.O3Determine job priorities and sequence job tasks in consultation with others in the workplace.

0577.E1.O4Identify workplace hazards and conditions and implement risk control measures following work health and safety requirements.

0577.E1.O5Select, fit and use personal protective equipment (PPE) required for the task.

0577.E1.O6Select tools and equipment for the task, check for serviceability, rectify and report faults.

0577.E1.O7Identify components for shopfitting units, safely handle and locate ready for assembling.

E2Assemble carcase.

0577.E2.O1Assemble carcase with faces and edges flush, and secure joints with specified fixings.

0577.E2.O2Square carcase, temporary brace and fix back, position and install shelves and mullions/divisions.

0577.E2.O3Square and wind adjoining surfaces, close fit face panels flush with surfaces.

0577.E2.O4Position and fix plinth or kicker to specified location.

0577.E2.O5Prepare and secure external fixed panels to carcase using specified method and fixings.

E3Fit bench and assemble and fit drawers.

0577.E3.O1Assemble bench or countertop components in preparation for installation.

0577.E3.O2Position bench or countertop on carcase to specified dimensions and fix using specified fixings and fasteners.

0577.E3.O3Edge drawer fronts, assemble drawers with bottoms fitted and fixed, and fit handles.

0577.E3.O4Determine drawer runner type from job requirements and install to manufacturer specifications.

0577.E3.O5Apply specified clearances to install drawers parallel to carcase bottom.

E4Fit doors.

0577.E4.O1Edge doors and drill for and fix hinges and handles.

0577.E4.O2Hang doors to carcase with faces flush and allow specified clearances.

0577.E4.O3Sand surface edge finishes to job requirements and clean unit in preparation for coated finish.

E5Prepare units for transport.

0577.E5.O1Disassemble internal shopfitting units that are too large for transport or too heavy for safe lifting into smaller components and sections.

0577.E5.O2Determine and arrange packaging requirements for smaller and separate components.

0577.E5.O3Label disassembled components and sections, and place in a safe and appropriate area ready for collection.

0577.E5.O4Number and locate assembly diagram for inclusion in delivery instructions.

0577.E5.O5Safely store shopfitting units and components to avoid damage to surfaces.

E6Clean up.

0577.E6.O1Clean tools, equipment and machinery, check for serviceability and report damage or faults.

0577.E6.O2Clear work area and dispose of, reuse or recycle materials following workplace and environmental requirements.

0577.E6.O3Store and secure tools and equipment following workplace procedures.