SKILLS PORTAL

ព្រះរាជាណាចក្រកម្ពុជា · KINGDOM OF CAMBODIA

Cambodian Skills Delivery Model

SEAL National Course Catalogue · MLVT / National Training Board

Sector Frameworks

1,164

Qualifications

15,161

Competency Units

10,938

Elements

41,782

Learning Outcomes

2,822

Assessment Packages

Set up, operate and maintain indirect action powder-actuated power tools

KHU-CON-0127

Australian Equivalent

CPCCCA3027

Elements

Learning Outcomes

This unit of competency specifies the skills and knowledge required to set-up, operate and maintain powder-actuated power tools safely and effectively to fasten materials or fix fasteners to bases, meeting all relevant requirements of work health and safety (WHS), and Commonwealth and state or territory legislation. Completion of the general construction induction training program specified by the model Code of Practice for Construction Work is required for any person who is to carry out construction work. Achievement of CPCWHS1001 Prepare to work safely in the construction industry meets this requirement. No licensing, legislative or certification requirements apply to this unit at the time of publication.

Elements & Learning Outcomes

E1Plan and prepare.

0127.E1.O1Read and interpret work instructions and plan sequence of work.

0127.E1.O2Plan all work to comply with laws and regulations, work health and safety (WHS) and environmental requirements, manufacturers’ specifications, workplace requirements, drawings and specifications.

0127.E1.O3Select tools and equipment, check for serviceability and rectify or report any faults.

0127.E1.O4Select and use personal protective equipment (PPE) for each part of the task.

0127.E1.O5Inspect work site, locate services, assess hazards and apply risk controls, including required signage and barricades.

E2Set out fasteners.

0127.E2.O1Set out fasteners, adhering to minimum distances from edge of substrate material.

0127.E2.O2Position and hold or fix material into designed position.

E3Prepare powder-actuated power tool.

0127.E3.O1Strip, check and reassemble tool.

0127.E3.O2Check tool for operation and test fire following manufacturer’s specifications and WHS requirements for use of powder-actuated power tools.

0127.E3.O3Select fastener.

0127.E3.O4Assess requirements for material, base and penetration and select charge.

0127.E3.O5Install attachments and accessories to tool following manufacturers’ specifications and WHS requirements for use of powder-actuated power tools.

0127.E3.O6Locate fastener and charge in powder-actuated power tool to manufacturers’ specifications.

E4Operate powder-actuated power tool.

0127.E4.O1Operate tool to fix fastener in place to manufacturers’ recommendations, legislation, regulations and codes of practice.

0127.E4.O2Check fastening penetration, applying appropriate depth into material.

0127.E4.O3Adjust power regulating device for conditions.

0127.E4.O4Perform misfire procedures in accordance with manufacturers’ recommendations, legislation, regulations and codes of practice.

0127.E4.O5Remove temporary holding and fixings.

E5Maintain powder-actuated power tools and kits.

0127.E5.O1Check safety features of tools for serviceability in accordance with manufacturers’ recommendations.

0127.E5.O2Clean and lubricate tools to manufacturers’ recommendations.

0127.E5.O3Perform periodic maintenance service to manufacturers’ specifications.

E6Store powder-actuated power tools and charges.

0127.E6.O1Store charges in designated container in accordance with legislation, regulations and codes of practice, and record used charges.

0127.E6.O2Store unused fasteners, tool and attachments in carry case following manufacturers’ recommendations.

0127.E6.O3Check logbook and record maintenance.

E7Clean up.

0127.E7.O1Clean up, meeting all legislative and workplace requirements for safety, waste disposal and materials handling.

0127.E7.O2Record safety or waste disposal discrepancies in accordance with workplace procedures.